Quantcast

Search:

Type: Posts; User: majinga

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    120

    That's odd. I never seen a tv which don't let you...

    That's odd. I never seen a tv which don't let you to force the aspect ratio.
    Check the scart, to allow the TV to be auto set in 4:3 you need to feed about 12v on the scart PIN 8.

    Most of the time...
  2. With the fix you will be able to do the IGR in...

    With the fix you will be able to do the IGR in SMS mode, by holding B+C+DOWN for few seconds.
  3. Sensing the pin 7 make the fix available for...

    Sensing the pin 7 make the fix available for everyone who already have the mod, without the need to solder anything else.
  4. Replies
    732
    Views
    301,662

    No, still not able to see the attachment. Some...

    No, still not able to see the attachment.

    Some progress in the repair?
  5. At the moment the plan is to check the value on...

    At the moment the plan is to check the value on pin 7, if is stuck high then the MD is in SMS mode.

    Allow the micro to control the pin in such situation is not so easy. You can't just feed a...
  6. This is exactly what the SMS++ do. On the MD++...

    This is exactly what the SMS++ do. On the MD++ the micro is already capable to read the 3/6 pad buttons. This is easy.
    The complicated part here is to allow the micro to handle the pad only when the...
  7. Here some info about how the 6 buttons pad work:...

    Here some info about how the 6 buttons pad work:
    https://retroramblings.net/?p=835
    https://github.com/jonthysell/SegaController/wiki/How-To-Read-Sega-Controllers
  8. PIN 7 Is not suppose to stay fixed at one level,...

    PIN 7 Is not suppose to stay fixed at one level, vcc or ground. To allow the pad to work in 3 or 6 button mode PIN 7 must act like a clock. It continuously go high and low.
  9. It can but only in the menu. Once the game is...

    It can but only in the menu. Once the game is loaded it's up to the game to handle the pad.
  10. Replies
    732
    Views
    301,662

    Again, no attachment. You must melt the solder...

    Again, no attachment.
    You must melt the solder on each PIN together. Try to bend the single PIN is risky, you can apply too much force on the central pad.
  11. As roce said, this is game-specific. The...

    As roce said, this is game-specific. The everdrive can't do a generic patch for every game.
  12. Replies
    732
    Views
    301,662

    That's because it is a surface mount component....

    That's because it is a surface mount component.
    I would remove it with hot air. Probably is possible to use something like the chip quick to desolder it, but i would not use this method. Or just two...
  13. Replies
    732
    Views
    301,662

    Sorry, it's not clear to me. What do you mean?...

    Sorry, it's not clear to me. What do you mean?
    TR4 is an SMT component. Probably a to-252 or 263. Do you need some advice on how desolder it?
  14. Replies
    732
    Views
    301,662

    Correct. The fuse is gone. TR4 doesn't look...

    Correct. The fuse is gone.

    TR4 doesn't look good to me. I will replace it.
  15. From what i read, he feed the clock signal to the...

    From what i read, he feed the clock signal to the pad. For the mod on the SMS you have to cut the traces from the db9 connector. The micro take care to send back to the SMS the signals of the...
  16. I don't think there is a simple solution for...

    I don't think there is a simple solution for this. You neeed to feed the clock signal to the pad to get the start button. But only in the SMS mode. In the normal MD mode you must allow the clock from...
  17. No. At the moment the problem is that the micro...

    No. At the moment the problem is that the micro is not sending any reset sigal. Because It is not getting the right buttons combo.
    The fix will allow to use a different buttons combo in the SMS mode...
  18. The only way to fix this is change how the micro...

    The only way to fix this is change how the micro operate. I was thinking about an easy solution. Let me talk of this with SukkoPera, I'm sure we can arrange something.
  19. I suspect this. The MD pads are back compatible...

    I suspect this. The MD pads are back compatible with the SMS, same pinout. SEGA managed to have more buttons by adding a pulse singal, the pad send a different set of buttons at every rise or fall of...
  20. B2 is connected to the WRES line, which is the...

    B2 is connected to the WRES line, which is the same of the reset button. The purpose is to allow a cartridge to send a reset signal, like if the reset button was pressed.
    In the MD there are two...
  21. Replies
    33
    Views
    8,880

    This has nothing to do with the mod. When the...

    This has nothing to do with the mod. When the micro reset the console, is like when you press the reset button.
    B2 is the reset signal coming from the cartridge, but in the SMS mode the reset is...
  22. Replies
    33
    Views
    8,880

    Yes

    Yes
  23. Replies
    33
    Views
    8,880

    Here:

    Here:
  24. Replies
    33
    Views
    8,880

    You have to edit the Arduino sketch

    You have to edit the Arduino sketch
  25. Replies
    732
    Views
    301,662

    How do you get some voltage if the fuse is open?...

    How do you get some voltage if the fuse is open?


    Tr4 is a darlington transistor. It act as a power switch for the MCD. You must find voltage only on one side when is off, and on both when is on....
Results 1 to 25 of 146
Page 1 of 6 1 2 3 4